Pinnacle - Hitting the highest Point
DISCLAIMER :
This website [Pinnacle.withme.us] claims no credit for any information, news and/or images featured on this site unless otherwise noted. All visual content is copyright to its respectful owners. Information on this site may contain errors or inaccuracies too - we do not make warranty as to the correctness or reliability of the site's content. If you own rights to any of the images, and do not wish them to appear on this site, please leave a private message and it will deleted immediately.

By clicking on " LOGIN " below:
- You acknowledge to have fully read the Term of Service while you registering of this FORUM;
- You commit yourself to respect unreservedly these current rules;
- You grant the moderators of this forum the right to delete, move or edit any discussion subject at any moment.


Please visit http://datanetops.blogspot.com for more info.





 
HomeHome  FAQFAQ  PortalPortal   BLOG  RegisterRegister  Log inLog in  
Never provide your password to anyone, even if this person claims to be a forum moderator or administrator. For more information about this forum please read FAQ or visit datanetops.blogspot.com
Search
 
 

Display results as :
 
Rechercher Advanced Search
Latest topics
» Which Technology is Better: GSM or CDMA?
Mon Aug 23, 2010 1:14 pm by Boazdexter

» Cisco Router Simulator Software
Sat Jul 10, 2010 2:46 pm by Enforcer

» Ceragon Software
Sat Jul 10, 2010 2:42 pm by Enforcer

» Chariot v4.3.1212 for Windows (c) NetiQ
Sat Jul 10, 2010 2:36 pm by Enforcer

» IP Security Software
Sat Jul 10, 2010 1:01 pm by Enforcer

» Linux Application software
Wed Mar 31, 2010 11:19 am by Enforcer


Top posters
Enforcer
 
Congressman
 
jemscaburn
 
Boazdexter
 

Share | 
 

 Password Recovery Procedure for the Cisco 1700 and 1800 Series Routers

View previous topic View next topic Go down 
AuthorMessage
Enforcer
Private
Private


Posts : 28
Join date : 2010-01-31
Age : 36

PostSubject: Password Recovery Procedure for the Cisco 1700 and 1800 Series Routers   Tue Feb 02, 2010 5:49 pm

Components Used
The information in this document is based on these hardware versions:

· Cisco 1700 Series Router
· Cisco 1800 Series Router

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Related Products

Refer to Password Recovery Procedures for information on how to recover passwords for related products.

Conventions
Refer to Cisco Technical Tips Conventions for information on document conventions.

Step-by-Step Procedure
Follow these steps in order to recover your password:
1. Attach a terminal or PC with terminal emulation to the console port of the router.
Use these terminal settings:

o 9600 baud rate
o No parity
o 8 data bits
o 1 stop bit
o No flow control

Refer to these documents for information on how to cable and connect a terminal to the console port or the AUX port:

o Cabling Guide for Console and AUX Ports
o Connecting a Terminal to the Console Port on Catalyst Switches
o Connect a Terminal to Catalyst 2948G-L3, 4908G-L3, and 4840G Series Switches

2. If you can access the router, type show version at the prompt, and record the configuration register setting. See Example of Password Recovery Procedure in order to view the output of a show version command

Note: The configuration register is usually set to 0x2102 or 0x102. If you can no longer access the router (because of a lost login or TACACS password), you can safely assume that your configuration register is set to 0x2102.

3. Use the power switch in order to turn off the router, and then turn the router back on.

Important Notes:

o In order to simulate this step on a Cisco 6400, pull out and then plug in the Node Route Processor (NRP) or Node Switch Processor (NSP) card.

o In order to simulate this step on a Cisco 6x00 with NI-2, pull out and then plug in the NI-2 card.

4. Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON.

If the break sequence does not work, refer to Standard Break Key Sequence Combinations During Password Recovery for other key combinations.

5. Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.

This step bypasses the startup configuration where the passwords are stored.

6. Type reset at the rommon 2> prompt.

The router reboots, but ignores the saved configuration.

7. Type no after each setup question, or press Ctrl-C in order to skip the initial setup procedure.

8. Type enable at the Router> prompt.

You are in enable mode and should see the Router# prompt.

9. Type configure memory or copy startup-config running-config in order to copy the nonvolatile RAM (NVRAM) into memory.

Important: Do not type copy running-config startup-config or write. These commands erase your startup configuration.

10. Type show running-config.

The show running-config command shows the configuration of the router. In this configuration, the shutdown command appears under all interfaces, which indicates all interfaces are currently shut down. In addition, the passwords (enable password, enable secret, vty, console passwords) are in either an encrypted or unencrypted format. You can reuse unencrypted passwords. You must change encrypted passwords to a new password.

11. Type configure terminal.

The hostname(config)# prompt appears.

12. Type enable secret <password> in order to change the enable secret password. For example:

hostname(config)#enable secret cisco

13. Issue the no shutdown command on every interface that you use.

If you issue a show ip interface brief command in privilege EXEC mode, every interface that you want to use should display up up. For example:

Router#show ip interface brief

14. Type config-register <configuration_register_setting>. Where configuration_register_settingis either the value you recorded in step 2 or 0x2102. For example:

hostname(config)#config-register 0x2102 15. Press Ctrl-z or end in order to leave the configuration mode.

The hostname# prompt appears.

16. Type write memory or copy running-config startup-config in order to commit the changes.


[You must be registered and logged in to see this image.]
Back to top Go down
http://ajpuno.50webs.com
 
Password Recovery Procedure for the Cisco 1700 and 1800 Series Routers
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» PFO closure and recovery information
» Stimpath procedure, anyone?
» Using Webdriver java :Obtaining an OTP(Ont time Password) PIn from an registered email ID and use the value in an text box field of my Webapp URL.
» security-password-pop-up-coding
» password-protect

Permissions in this forum:You cannot reply to topics in this forum
Pinnacle - Hitting the highest Point :: Community Update :: Technical Help and Troubleshooting :: IP and Data Services-
Jump to:  
Forum create on Forumotion | © phpBB | Free forum support | Contact | Report an abuse | Free forum